How To Change Headlight On 2014 Nissan Versa

Nissan Versa Headlight Bulbs Replacement Guide
How to change a burnt out depression / loftier beam, plough point and side mark light bulb in a 2009 to 2012 Nissan Versa.

2019 Versa Headlight
Wait Behind Housing
Low & High Beam Bulb This automotive maintenance tutorial was specifically written to assist owners of the second generation 2012, 2013, 2014, 2015, 2016, 2017, 2018 and 2019 Nissan Versa sedan in changing a burnt out dual filament combination depression axle and high beam headlight bulb, front turn signal lite bulb or the forepart side mark calorie-free bulb.

Owners of other Nissan vehicle such as the Sentra, Altima, Maxima, Murano, Rogue,  Note, Leaf, Juke, Kicks, Latio, Almera, Sunny, Qashqai, NV200, Pathfinder, Frontier and X-Trail may too discover these DIY instructions to be helpful.

The compatible replacement light bulb part numbers are as follows: Low / High Axle # 9003 (HB2 H4), Front Turn Signal # 3457A (likewise known as 3457NA or 3457AK) and Front Side Marker # 2825 (also known equally W5W).

If y'all would like to take brighter headlight bulbs that will also last much longer before burning out compared to the traditional halogen and incandescent lite bulbs, install some 9003 LED, 3457A LED and 2825 LED bulbs.

Notation - The earlier 2012 and 2013 Nissan Versa model years were equipped with bayonet style front end turn betoken low-cal bulbs which are function number 7507 (also known PY21W).

Please check your quondam calorie-free bulbs before buying new ones. The correct calorie-free bulb part numbers might vary depending on the model twelvemonth, trim level and where your vehicle was manufactured.

The get-go two steps are to open the hood and motion to the side of the vehicle with the burnt out light bulb.

The headlight is a dual filament bulb that acts equally both the low beam and high beam lights.

Pull Off Power Plug
Pull Off Safe Embrace
Dust Cap Removed Gently pull the black plastic electrical connector direct off the 3 metal blades on the base of operations of the old light seedling.

If you have problem removing the power plug, try gently wiggling it back and along while pulling it direct off.

Advisedly pull the rubber grit cap off the dorsum side of the headlight housing.

Prepare the embrace bated in a prophylactic place.

Two Metal Retaining Bars
Push Frontwards & Down
Release Top Metal Bar The headlight bulb retaining clip has two metal confined that securely hold it in place.

Gently push button the cease of the lower arm frontward and then down out of the metallic hook on the bulb socket.

Echo the process to release the pinnacle arm of the retaining clip.

Swing Open Retaining Prune
Remove Old Light Bulb
Osram HB2 9003 H4 Seedling Swing open the two arms of the retaining prune to release the old light bulb.

Pull the sometime light bulb direct out of the socket in the headlight housing.

The OEM (original equipment manufacturer) light bulb was marked as part number Osram HB2 DOT 9003 L Germany Bilux 12V 60/55W H4 U 37R E1 00801 w8b7.

Make clean New Calorie-free Bulb
Empty Bulb Housing
Install New Headlight Bulb Avoid touching the glass part of the new halogen seedling with your fingers or anything greasy in the engine bay.

If you practice get the new bulb dirty, clean information technology off with a newspaper towel and some rubbing alcohol.

Whatever grease or clay left on the glass surface of the new seedling could lead to a hot spot which may reduce the life span of the bulb and crusade it to burn out prematurely.

Orientate the 3 metal tabs on the new seedling in the correct position.

Insert the new 9003 bulb into the opening in the rear of the headlight assembly.

If yous would similar to have bright headlights, install a uniform replacement 9003 LED seedling.

Secure Retaining Arms
Safety Droppings Cover
Push On Rubber Cover Swing the retaining bars back over the new base of the new light seedling.

Push the two retaining arms frontward and then secure them to the superlative and bottom hooks.

Push the rubber dust kicking dorsum into place over the base of the new light seedling.

Push On Power Plug
Side Marker - Outer Edge
Small Black Bulb Socket Line up the electric connector and push it back into place over the three metallic blades on the base of the new headlight bulb.

The front end side marker low-cal bulb is located at the rear outer edge of the housing.

Locate the modest blackness plastic bulb socket inside the engine bay.

one/4 Turn Counterclockwise
Pull Out Old Light Bulb
Old Low-cal Seedling Removed Rotate the base of the bulb socket 1/4 turn in the counterclockwise direction before pulling it straight out of the housing.

Gently pull the old low-cal bulb straight out of the socket.

If you lot have trouble removing the former bulb due to corrosion (rust) or other debris, try carefully wiggling the seedling dorsum and forth before pulling information technology straight out.

Push In New Light Bulb
Empty Bulb Housing
1/four Turn Clockwise Button a new number 2825 miniature wedge base light bulb straight into the socket.

If y'all'd like to accept brighter front side marking lights, install a pair of uniform replacement 2825 LED bulbs.

Re-insert the bulb socket into the opening in the rear of the housing and rotate it ane/four turn in the clockwise direction to secure it into identify.

Turn Signal - Inner Corner
ane/4 Turn Counterclockwise
Front Turn Signal Low-cal The front turn signal light bulb is situated at the inner edge of the housing.

Reach down into the engine bay and rotate the round orange / tan colored plastic bulb socket 1/4 turn in the counterclockwise direction before pulling information technology straight out.

Pull Out Old Light Seedling
Old Light Seedling Removed
Push In New Plough Bespeak Carefully pull the onetime wedge base turn signal calorie-free seedling straight out of the socket.

If you accept problem removing the one-time light bulb due to rust, sand or other debris, put on some protective gloves and gently wiggle the bulb back and forth while pulling it straight out.

Avoid using excessive pressure on the erstwhile bulb to prevent from having it pause and cut your fingers.

If you accept a 2014, 2015, 2016, 2017, 2018 and 2019 Versa, the compatible replacement light bulb should be the 3457AK (also known as 3457A or 3457NA).

If you have an earlier 2012 or 2013 Versa, the owner's manual lists the uniform front plough signal light bulb as being part number 7507.

For the 7507 bayonet style lite bulb with the circular base, you will need to push button the bulb down into the socket and rotate it 1/4 plow in the counterclockwise direction before pulling it straight out. Then to install a new bayonet style seedling, button it down into the socket and rotate information technology 1/4 plough in the clockwise management to secure it into place.

Push a new wedge base 3457AK light bulb down into the socket.

i/4 Turn Clockwise - Lock
Examination New Calorie-free Bulbs
Headlight Bulb Replaced Re-insert the bulb socket into the housing and rotate it 1/4 turn in the clockwise direction to secure it into identify.

To test the new light bulbs, turn on the parking lights, turn on the headlights, flash the high beams and actuate the hazard signals.

Tip - If yous installed an LED bulb and it doesn't piece of work, effort removing it from the socket, rotate it 180 degrees and push it back into the socket. Some brands of LED bulbs are "polarized" and will only work when the "+" positive and "-" negative electrical contacts are in the correct orientation.

Be sure to write down the bulb alter in your motorcar's service records.

Delight check out all of my 2012-2019 Nissan Versa DIY Repair & Maintenance Guides.

Source: https://www.paulstravelpictures.com/2012-2019-Nissan-Versa-Headlight-Bulbs-Replacement-Guide/

Posted by: quinnoloplath.blogspot.com

Share this post